Rogue Barbell Club

[Mech6]

It almost looks like the arm would swing back and hit the lower mount pin and knock it out.. lol. I doubt it does, but man there must be almost no clearance. Price seems reasonable, though.

Curious what the increase will be for monster version. Because those attachments (monster series) all have plastic in back to protect upright... And their locking pin won't work the way they have it now. The 1" pins are quite a bit longer, to accept the hairpin at the end. I assume they'll just drop the 2nd hole another 2 or 4".

[Cleveland33]

There is zero chance you could fit the pin handle on the inside and have it not hit.. Right?

I don't see why that would be a problem other than maybe bending the handle a bit.

[Sdca7718]

If you look closely you will see it can't hit the pin out. The UHMW on the arms rests against the frame and it isn't pushing on the pin. Unless I'm missing something I think they thought of that.

[THErunCMD]

If you look closely you will see it can't hit the pin out. The UHMW on the arms rests against the frame and it isn't pushing on the pin. Unless I'm missing something I think they thought of that.

That looks right. Also prevents the metal on metal contact of the bracket to jhook. Still prefer my Mech6 version

[Robfitx]

http://www.roguefitness.com/rogue-ad...t-monster-lite

Really tempted to put this on my wishlist for my RML-390F, but I notice their website says to use it for bolted down racks. Not sure why this wouldn't work on my rack?

[thejosef]

Really tempted to put this on my wishlist for my RML-390F, but I notice their website says to use it for bolted down racks. Not sure why this wouldn't work on my rack?

It will work, but I'm sure they are just being extra cautious since the weights actually swing back when you re-rack. Do you have weights stored on your rack to weigh it down any?

I hope someone buys this newer design and reports back. I'd love to hear some feedback on it.

[Bench905]

A little late, but finally was able to get a pic of my gear.

Ballistic block
SISU War Hammer
Econ Lifting Belt
White wrist wraps

#23!

||---|| Rogue Barbell Club ||---||

#1 - Bench905
#2 - VMango
#3 - rlundregan
#4 - pandobearninja
#5 - irongrandpa
#6 - swimmer32
#7 - thejosef
#8 - snova031
#9 - smokinHawk
#10 - rpark
#11 - Stasher1
#12 - throwaway3441
#13 - Sdca7718
#14 - JoeCdn
#15 - Robfitx
#16 - whitessp
#17 - Xone
#18 - BuckeyeROC
#19 - useport80
#20 - 1651Naismith
#21 - okeley
#22 - keyboardworkout
#23 - dac22
#36 - mrcheeze36
#65 - dragon360
#998 - FyrFytr998

So I guess I have to upgrade to ML series now? Might as well go for color, right?

[Robfitx]

It will work, but I'm sure they are just being extra cautious since the weights actually swing back when you re-rack. Do you have weights stored on your rack to weigh it down any?

I hope someone buys this newer design and reports back. I'd love to hear some feedback on it.

I see what you mean, hadnt thought about the fact that it swings back with the weights on it. I am not currently storing plates on it because it seems like doing so would either interfere with bench press or squats depending on placement. I have read about others storing plates on it and not interfering but I just can't picture it so I haven't invested in the storage bars to experiment with.

[urbanlifter]

Not sure if anyone has seen this limited edition bar, I ran across it today looking at the 'New' stuff and thought the gunmetal looked awesome.

[Xone]

So I guess I have to upgrade to ML series now? Might as well go for color, right?

on ******** rogue said they were going to make an adapter for the infinity series. not sure what that will look like but I asked them.


I don't even need a monolift and don't compete in federations that allow a monolift so I'm probably better off never getting one and walking everything out, but I may not be able to help myself if there is an adjustable infinity version.

[ASOUL]

Not sure if anyone has seen this limited edition bar, I ran across it today looking at the 'New' stuff and thought the gunmetal looked awesome.

Yeah, it has been out for a couple weeks now. When it first showed up on Rogue Canadian site, it showed the price at $4,000! It blew my mind that the finish would cost that much more, but looks like they fixed the price error some time after.

[twelveosix]

Hey guys, just wondering how you guys clean your barbells? Like how do you use get rid of chalk, what oil do you use? Also, any advice on how to prevent knurl from.getting used up by j hooks without using those polystyrofoam things

[THErunCMD]

on ******** rogue said they were going to make an adapter for the infinity series. not sure what that will look like but I asked them.


I don't even need a monolift and don't compete in federations that allow a monolift so I'm probably better off never getting one and walking everything out, but I may not be able to help myself if there is an adjustable infinity version.

While it's great for squatting and I love my Mech6 mono lift hooks for that...where it really shines is benching. Like getting a perfect handoff every time.

[Xone]

While it's great for squatting and I love my Mech6 mono lift hooks for that...where it really shines is benching. Like getting a perfect handoff every time.

yeah that's what I'm thinking and may just use it for that so I still get walkout practice. will be good since I want to start doing more slingshot bench again.

[throwaway3441]

Looks like the new trap bar snuck out:



$345 plus freight shipping. Freight shipping is $133 to Florida so you're looking at nearly $500.

They acknowledge their ****ty powder coating:

PLEASE NOTE: Because the TB-2 Trap Bar is finished in our Rogue signature black powder coat, any metal-to-metal contact with the coated sleeves (such as adding and/or removing plates) may cause wear on the finish over time.

I'd like to upgrade from my BWTG bar to something that's rackable, has regular and raised handles, and has long sleeves but $500 is a bit steep.

[TipsyBanker]

Finally pulled the trigger on the base for my home gym ... went all Rogue to save on shipping costs ($160 for everything to Canada) and got a sweet deal on a gift card off ebay

- R3-BT (30'')
- Flat Utility Bench (Also bolt together)
- Ohio Power Bar in black/bright zinc
- Set of 1.25lb plates
- Rogue HG Collars (free )

Will post pics on delivery ... been "pending delivery' for 2 days now

[Synthetickiller]

Looks like the new trap bar snuck out:
$345 plus freight shipping. Freight shipping is $133 to Florida so you're looking at nearly $500.
They acknowledge their ****ty powder coating:
I'd like to upgrade from my BWTG bar to something that's rackable, has regular and raised handles, and has long sleeves but $500 is a bit steep.

It looks like a nice bar. $500 is hard to swallow. What is the most comparable trap bar vs this one?
Is this powder coating typical of rogue bars in general? I've seen a lot of finish related issues.

[keyboardworkout]

The TB-1 weighs 80 pounds and the TB-2 weighs 60 pounds.

Sounds like they aren't using solid sleeves and charging $50 more.

[snova031]

It looks like a nice bar. $500 is hard to swallow. What is the most comparable trap bar vs this one?
Is this powder coating typical of rogue bars in general? I've seen a lot of finish related issues.

I don't know of any other rackable trap bars w/ raised handles. York and Cap make trap bars with raised handles (York's also has a kickstand), but neither are rackable, IIRC.

That said, I'd imagine Dean can add raised handles to his regular rackable hex bar, and probably come in under $500.

As for their powder coating, I only have a Matador to compare, but I've found it to be inferior to my BWTG pieces. The coating on my Matador has chipped in several spots.

[jaketaylor]

Fortis 3 Power Rack
Bumper Plates
Flat Bench
Ohio Bar
Deadlift Jack
Safety Straps
Multi Grip Pullup Bar

rogue_club.jpg

[Stasher1]

I don't know of any other rackable trap bars w/ raised handles. York and Cap make trap bars with raised handles (York's also has a kickstand), but neither are rackable, IIRC.

That said, I'd imagine Dean can add raised handles to his regular rackable hex bar, and probably come in under $500.

As for their powder coating, I only have a Matador to compare, but I've found it to be inferior to my BWTG pieces. The coating on my Matador has chipped in several spots.

The York Multi-hex won't fit on the bar hooks due to the configuration of its ends, but it will work across the safeties.

[throwaway3441]

That said, I'd imagine Dean can add raised handles to his regular rackable hex bar, and probably come in under $500.

Roughly $400, and that's with $160 shipping:

Custom Trap bar.

95# currently.

Solid handles. 6" raise.
Solid loading area. 20" space

@Leo Desforges shipping on this alone is 140-160. Around the 375-400 range.

On ******** he said UPS gets quite a bit more expensive when you reach 75" wide and that's why the sleeves on his rackable hex are so short. He says he can make extensions but I've asked a few times how much they cost and whether they'll work with spinlocks but he never responded.

[jedpop]

The York Multi-hex won't fit on the bar hooks due to the configuration of its ends, but it will work across the safeties.

I bought the Slayer Barbell Rackable Hex Bar (it has raised handles). I'm not sure what's going on at Slayer Barbell since many of their product are currently out of stock but the price of the bar is $349 with free shipping (I think there is also a coupon code available for it (I used "INTENSE" FOR 10% off)).

Positives:
Jim @ Slayer answered all questions promptly
"Normal" Olympic plate loading end diameter (Prolocs and Olympic (non-specialty) Lock Jaws work on the bar)
Weighs 45 lb
84" long
Packaging was the best I have ever seen fitness equipment shipped in (almost zero chance of damage during shipping)
Solid welds
Nice, even, mildly aggressive knurl
Nice finish on center portion (see Negative about the plate loaded ends)
Price (at $314 + free shipping)

Negative (just one issue):
Painted plate loaded ends has flaked off on one 1"x2" area - does not seem like a real problem because no rust developing since I use it twice a week.

Overall, I am very happy and have no regrets with the bar.

[throwaway3441]

I'm not sure what's going on at Slayer Barbell since many of their product are currently out of stock...

From their ******** page it looks it was a small side business and it didn't survive the move from Illinois to Florida. That's a shame.

[swimmer32]

I'm hoping Rogue puts on a "Free Shipping" deal for the 4th of July, but I'm not holding my breath. Do they typically only have sales on Black Friday?

[mrcheeze36]

I'm hoping Rogue puts on a "Free Shipping" deal for the 4th of July, but I'm not holding my breath. Do they typically only have sales on Black Friday?

Yeah, it's usually on Black Friday only (sales and 5 for $5 shipping). I don't recall seeing anything else throughout the year.

[g8rlaw]

I got recently got a Rogue flat bench and 160lb set of Echo bumpers. That makes 3 Rogue pieces for me, so I guess I should request a Rogue number now.

Rogue Matt Chan Bar
Rogue Flat Bench
Rogue Echo Bumpers

[FyrFytr998]

Checking in. Finally back at it, and finished my first week on my Rogue equipment. Quality all around. Two controlled dump outs on my SML-1 during squats and the rack handled them like a champ.

The Ohio Power is awesome, although having a quality center knurl will take some getting used to. My traps were rubbed raw during skwatts today. Had to use a manpon for my accessory squat work, it was that distracting. I will also add that even keeping the bar coated in a relatively humid free basement, the bare steel bar is a bitch to keep from oxidizing. When I wipe the bar down, the rag usually comes off red.

Any suggestions? Is WD40 not optimal?

[TipsyBanker]

for those who ordered stuff off rouge canada how long did shipping take? My order has been "pending shipping" for one week now ...

[drrickso]

Checking in. Finally back at it, and finished my first week on my Rogue equipment. Quality all around. Two controlled dump outs on my SML-1 during squats and the rack handled them like a champ.

The Ohio Power is awesome, although having a quality center knurl will take some getting used to. My traps were rubbed raw during skwatts today. Had to use a manpon for my accessory squat work, it was that distracting. I will also add that even keeping the bar coated in a relatively humid free basement, the bare steel bar is a bitch to keep from oxidizing. When I wipe the bar down, the rag usually comes off red.

Any suggestions? Is WD40 not optimal?

how about a dry liquid protectant like tuf glide (or use tuf cloth) from sentry solutions?