Misc tradies recommend me what electric drill to buy (200k reps) (srs advice needed)

[backinthegymbro]

I need to put together some planks to make a ''table'' for the DIY business i'm running. It's really important to me so i'd really appreciate the help.
The wooden beams are 1.7x2.7 inches thick.

My original idea was to drill screws into it. I bought a new drilling machine, but it either wasn't powerful enough or the screws had the wrong end at the top. Because it wouldn't drill the holes in even the slightest bit. The screws had some weird 6 pointed star at the top so i didn't have the proper screw add on for the drill.

Question 1: If it is possible to easily drill screws into these wooden beams, how strong must the drill be? So i buy a drill that has a battery or should i get a chord one?
How much power must it have? What should i look for?

Question 2: I also need to drill some holes into my concrete wall to put up some shelves.
Do i need a specific drill for that? Or can the same ''powerful'' drill that i'll buy for the wood, do the job for the concrete?

Question 3:What is an impact drill? Do i need it? Can an impact drill switch settings from regular to impact?

Question 4: Someone recommended i simply use nails instead of screws.
However the nails that are long enough (4 inches) are all super thick. There's no way i can hammer those through the beams.
So is drilling the only way or should i look for long thin nails?



Question 5: What ''table'' leg is more secure?

[QuickShotSteve]

Milwaukee m18, dont get anything else

can do wood no problem and concrete. If you are going to do a lot of concrete get an SDS max hammer drill (also milwaukee m18)

Impact driver is fine for screws, but would not use for concrete, the standard drill is more versatile

[Battlefury]

Buy something like this, and pair it with a screw driver and use a long screw.

https://www.homedepot.com/p/Milwauke...22CT/305491315

[RealAesthetic]

Milwaukee m18, dont get anything else

can do wood no problem and concrete. If you are going to do a lot of concrete get an SDS max hammer drill (also milwaukee m18)

Impact driver is fine for screws, but would not use for concrete, the standard drill is more versatile

this guy knows

Bosch 1-9/16-in SDS-max is the goat for concrete


I do mostly steel though so if you ever need a good mag drill recommendation i'm your man
still use above drills for misc stuff at work, even burn through steel with the miluak

[Battlefury]

This looks good enough.

https://www.homedepot.com/p/Milwauke...4023/314335901

[backinthegymbro]

Besides the recommended drills, what specifics should i look for? The power, watts, anything? Please educate me. I'm losing a lot of money not being able to put these tables together.

[Battlefury]

Besides the recommended drills, what specifics should i look for? The power, watts, anything? Please educate me. I'm losing a lot of money not being able to put these tables together.

The stuff that I posted should be good enough, it can last a long time. Wood is easy to drill.

[RealAesthetic]

Besides the recommended drills, what specifics should i look for? The power, watts, anything? Please educate me. I'm losing a lot of money not being able to put these tables together.

recommended miluak will suite all your needs as it's one of the most powerful hand drills for said purpose on the market, almost equally important is what bit you're using and what the dimensions of the hole are.

[ChrisLS8]

You need an SDS for concrete. Also get the milwaukee dust trap or a good respirator as concrete dust is no good.

You can use a Hammer drill for smaller holes in concrete. Any 18v will have more than enough power for wood screws and small lags

Makita, Dewalt, Ridgid, Milwaukee or even the new Ryobi brushless are good.

If you plan on buying more tools down the road look at what tools are in the battery ecosystem if you plan to expand. I personally have Milwaukee for some things (lights, sawzalls and impacts) and Dewalt for others (saws) and Makita for yet other things (sheet metal nibbler)

[backinthegymbro]

Right now drilling through the wooden beams is my top priority. I rather not spend $300 on a drill unless i absolutely have to.
I'll look into the recommendations. thank you.

[ChrisLS8]

Right now drilling through the wooden beams is my top priority. I rather not spend $300 on a drill unless i absolutely have to.
I'll look into the recommendations. thank you.

Get a hammer drill then it's dual purpose. My M12 and M18 have the ability to switch between regular drilling and Hammer drill for concrete. That way you don't need to get two tools.

Buying good quality german or swiss made bits will save you alot of time and aggravation. (Dewalt, Bosch, Diablo)

[bigdownunder]

Just hire a tradie to do the work for you.

They will do a better job, and you won’t be left with a bunch of tools that you only use once every three years.

It will probably be cheaper as well.

[steeler505]

Milwaukee m18, dont get anything else

can do wood no problem and concrete. If you are going to do a lot of concrete get an SDS max hammer drill (also milwaukee m18)

Impact driver is fine for screws, but would not use for concrete, the standard drill is more versatile

i gotta say boyo
that is one good lookin drill

[Kay4Kool]

Makita crew

[Brozef]

Milwaukee m18, dont get anything else

can do wood no problem and concrete. If you are going to do a lot of concrete get an SDS max hammer drill (also milwaukee m18)

Impact driver is fine for screws, but would not use for concrete, the standard drill is more versatile

The M12 impact is awesome too. I have one of these at work and at home. The one at work has had so many hot suppers and is going strong. I mean I have really been hard on that thing and it just won't quit. I had to buy one for myself.

Need to send a torx head screw through many inches of wood? No problemo muchacho

[usersignup2]

Is this wooden beam structural?

[IronFeta]

Use a Phillips screw driver and get an awesome arm workout

[Magomed1]

Milwaukee m18, dont get anything else

can do wood no problem and concrete. If you are going to do a lot of concrete get an SDS max hammer drill (also milwaukee m18)

Impact driver is fine for screws, but would not use for concrete, the standard drill is more versatile

This^^^

If you're doing a lot of concrete drilling a hammer drill combo is the way to go. Just make sure you drill in straight.

You also might need anchors or epoxy to hold the shelve screws in place.

[backinthegymbro]

What's the difference between these drills? With one, you get 2 drills for the same price. Are these lesser quality ones?

[ChrisLS8]

What's the difference between these drills? With one, you get 2 drills for the same price. Are these lesser quality ones?

Second ones are Brushless as well and are the older model.

The Fuel M18s are Brushless, way more power and heaps better than the old versions. Also check out Zoro.com for deals on tools

Are you planning on getting more tools down the road?

[JonEh10]

https://www.amazon.com/Milwaukee-289...1546939&sr=8-8

[ChrisLS8]

Honestly just run to Home Depot and get this

https://www.homedepot.com/p/RYOBI-18...1813/300225309

Ryobi brushless tools are plenty quality for a guy using em at home. There are even guys on job sites using em


Or this

https://www.homedepot.com/p/RIDGID-1...9205/206127587

[nickh04]

^ This.

If you aren't gonna be using them to make a living, then I would suggest Ryobi or Ridgid. They are a lot cheaper then brands like dewalt/milwaukee and they will do the job just fine.

I've used ridgid for years and never had a problem with them. They are just bulky and heavy compared to others.

[ispy]

i have a chit one, but if i was shopping for one, i'd probably go with a brushless milwaukee drill w/ 18 volt 5-6ah (anything lower is potato stuff) battery. it won't be cheap, but if you want quality, then this will probably be it. you need specialized drill bits for different surfaces. there's tons of them at places like home depot and amazon.

[TryingBB]

Dewalts are good. Only need to buy one and you’re forever good.

How big are the screws? Hopefully you’re gonna remember to drill some pilot holes and then put those screws in - you may crack the wood otherwise. Ask me how I know

[backinthegymbro]

^ This.

If you aren't gonna be using them to make a living, then I would suggest Ryobi or Ridgid. They are a lot cheaper then brands like dewalt/milwaukee and they will do the job just fine.

I've used ridgid for years and never had a problem with them. They are just bulky and heavy compared to others.

I just need a drill that will work. Whether it's cheap or expensive. But i need to get the job done.
It would be nice to have a drill that's versatile enough to drill through wood and concrete so i don't have to order 2. But right now drilling in wood is the most imortant.

Dewalts are good. Only need to buy one and you’re forever good.

How big are the screws? Hopefully you’re gonna remember to drill some pilot holes and then put those screws in - you may crack the wood otherwise.

The screws are 4 inches. I need to drill through 2 inch of wood.

. Ask me how I know

How'd you know?

[BootneckBrah]

For home DIY a cheap Bosch 18v combi got you covered fam.

For actual workhorses, Milwaukee, Hilti, Makita and DeWalt are professional choices.

You don’t need those in your home toolbox though unless, like me, you’re a label queen.

My personal preference is for Makita for durability and versatility vs Price

[TryingBB]

I just need a drill that will work. Whether it's cheap or expensive. But i need to get the job done.
It would be nice to have a drill that's versatile enough to drill through wood and concrete so i don't have to order 2. But right now drilling in wood is the most imortant.



The screws are 4 inches. I need to drill through 2 inch of wood.




How'd you know?

Any drill really can do the job - my first drill was $20 and I bought it on sale at CVS or some chit. But battery lasted me a year or two with minimal use.

So any drill will do the job - how? You need to use the right drill bit. For wood and drywall you can use any drill bit really but using the right one makes it just right. For concrete and steel
And tile, specially porcelain and you need to for sure have the right bits or you’ll be breaking bits and getting really frustrated.

To screw stuff in, make sure the bit you use fits real snug into the screw. It will give your bit and screw maximal contact and your drill machine should not pop out of there abs have a solid screw-in action. This is important when working with aluminum/steel as the screws are usually on there very tight with anti-slip liquid on there (the blue stuff you find on machines screwed). This will save you bits and also stripped screw heads

About the how I know - lol - well I thought it’s only a small screw - and I went to town with it. It cracked the wood. If you’re hanging a pic you’re ok but if you’re putting thick screws in, order I’ll a pilot hole. Depending on how thick (wide not long) the screw is, you’ll want a hole maybe half the width of the screw to get a snug fit. But I’m no wood expert so do your own research. I’m just a self taugh handyman who likes to do as much as possible by himself. If a job will take more than an hour and a half I get a handyman or professional in.

[ChrisLS8]

If you want good phillips bits if you can order online I use Vega 1" PH2 bits, they work better than anything I've used in years of being a tradie.

If possible try to buy Torx or Robertson (square drive) bits, they cam out alot less and are easier to drive in than phillips. For whatever reason they never really caught on.

I convinced my company to start the switch over to Torx drive

[TBO1313]

The "star" looking top is called a torx bit. As far as drills people have already mentioned Milwaukee which is top tier and DeWalt is up there too. If you want to go a little cheaper Makita is really good. I have a Makita drill from the 80s that's still going strong. If you wanna go even cheaper Ryobi is good. I've got a Ryobi drill that I've used for years and even drilled through concrete walls a couple times to hang stuff at my wife's office

If you want good phillips bits if you can order online I use Vega 1" PH2 bits, they work better than anything I've used in years of being a tradie.

If possible try to buy Torx or Robertson (square drive) bits, they cam out alot less and are easier to drive in than phillips. For whatever reason they never really caught on.

I convinced my company to start the switch over to Torx drive

Phillips head are supposed to slip. They work well in applications where you don't want to overtorque the screw.