Mopar Thread. Who's in the brotherhood of Muscle?

[BJoe]

Well to be fair, i'm going to take them off and plasti-dip them black, then put them back on lol.

Especially with the color i chose for my charger SP. It'll look good.

Plastidip that part of the bumper too so it doesn’t look like the bumpers Clives posted then!

[1QWIK7]

I bought him from a one plate state, so the dealer didnt add the front plate holder. Luckily the cops in Texas dont really give a **** about the front plates not being on the front



They extended the Power Dollars program to 2020 vehicles. Would sweeten the deal to buy instead of lease.

Take those banana guards off.... it looks dumb and does this:





I left those stupid guards on during the road trip from FL to TX when I bought my hellcat and it was filthy as f**k after 1100 miles under them. I had to detail the splitter a few times before the dirt outline came out.

Too late, i went ahead with the lease lol. If i was going to buy a charger, i would have went with that used hellcat, not a SP or 392 daytona. Plus, the next gen is coming in 2022-2023 no?

I'm not worried about the bumper leaving the guards on, it's a factory installed piece. I can't get penalized for it when it's already there from factory lol. I may do what the other guy said and plastic dip underneath the guard just in case it gets F'ed up.

[ClivesTriceps]

I'm not worried about the bumper leaving the guards on, it's a factory installed piece. I can't get penalized for it when it's already there from factory lol. I may do what the other guy said and plastic dip underneath the guard just in case it gets F'ed up.

it literally says "to be removed by dealer" on the front of the guards lol. It's only on there for shipment purposes. Removing them is a part of dealership PDIs

you do you, boo.

[1QWIK7]

it literally says "to be removed by dealer" on the front of the guards lol. It's only on there for shipment purposes. Removing them is a part of dealership PDIs

you do you, boo.

lol does it really say that?? idk. I didn't get my SP yet.

So if the dealer leaves them, then it becomes the owners responsibility to remove them?

If i get the car with them on, i'll leave them. If they remove it for me then i'll obviously not run them.

[Murph0408]

ohh don't be that guy. take the guards off.

be prepared for that piece to take a beating if you're using the car regularly/daily. I've tried to be careful with that front lower "Valance" piece, and it doesn't look shabby, but if one thing on the whole car will show its age it's that. especially in certain parking lots with curbs, you are very prone to scraping it.

retrospectively i wish i backed in a little more often over the last couple years.

[mingrey02stg2]

Reminds me of this:

https://www.thedrive.com/news/32061/...plitter-guards




Please take them off... they look ridiculous.

[Murph0408]

lol buncha dorks. it's like leaving the tags on your clothing.

smh

[shmobin]

Well to be fair, i'm going to take them off and plasti-dip them black, then put them back on lol.

Especially with the color i chose for my charger SP. It'll look good.

It will be all fun and games until one falls off on the freeway and you're left with a fuked up looking bumper.

[ClivesTriceps]

It will be all fun and games until one falls off on the freeway and you're left with a fuked up looking bumper.

If only they'd fall off.. They're secured by clips underneath the splitter

[1QWIK7]

ohh don't be that guy. take the guards off.

be prepared for that piece to take a beating if you're using the car regularly/daily. I've tried to be careful with that front lower "Valance" piece, and it doesn't look shabby, but if one thing on the whole car will show its age it's that. especially in certain parking lots with curbs, you are very prone to scraping it.

retrospectively i wish i backed in a little more often over the last couple years.

Damn, it's that bad huh? Idk i always had cars with splitters so i figure if i paint those guards black, with the color i chose for my SP, it'll kinda look like a splitter lmao.

I guess i'll take it off. I have better taste than that. I just figured since it's a lease, who cares what happens to the bumper. I'm not even sure if the car will even come with them. When i went to the dealer, i saw some cars with the guards on, some without. All of them were brand new. RT's and SP/392 daytonas etc.

[ClivesTriceps]

Damn, it's that bad huh? Idk i always had cars with splitters so i figure if i paint those guards black, with the color i chose for my SP, it'll kinda look like a splitter lmao.

I guess i'll take it off. I have better taste than that. I just figured since it's a lease, who cares what happens to the bumper. I'm not even sure if the car will even come with them. When i went to the dealer, i saw some cars with the guards on, some without. All of them were brand new. RT's and SP/392 daytonas etc.

you got any pics of your scat pack yet?

[1QWIK7]

you got any pics of your scat pack yet?

It should be coming soon. I keep checking the website for it (since it's still there) and it says, "in transit". Plus i'm waiting for my salesman to call me to come get it.

I'm debating on waiting for a bit longer anyway to go pick it up. They cut their hours short, can only go inside the actual dealer by appointment, and there's only like 1 or 2 salesmen there. Getting a new car isn't a 20 minute affair, you're there for hours. Even if you tell them to prep everything. I already told them don't wash the car lol.

[BJoe]

Got all of the “tune up” parts for my 200!

Already had one of RPM Motorsports intake tubes for the ‘11-‘14 3.6l Avenger and 200 that replaces the corrugated intake tube with resonator chambers, then as of today, I now have new stock replacement iridium plugs from Champion, MSD Coils for the Pentastar V-6 as well as the Pentastar “Upgrade” lower intake manifold that flows more air stock than the factory lower would after going to town on it with a grinder for a little porting work! The Mahle parts bag is just gasket for the intake, didn’t even need special gaskets either, the stock replacements for the original design are a direct fit to the “upgrade” part!

https://www.instagram.com/p/B-3AmSqj..._web_copy_link