|
Thread: My recent builds
-
01-13-2019, 04:39 PM #3271
-
01-13-2019, 04:43 PM #3272
The axial rotation of the landmine/barbell would mess everything up. Any small shift and the whole thing would swing to one side or the other. At it's cheapest, this thing only requires a tube with 2 holes (one for pivot, one for locking pin), a pin or band peg long enough to traverse 2 tubes (to act as pivot), and a hitch pin (to lock).
▪█──█▪ Equipment Crew #61 ▪█──█▪
-
-
01-22-2019, 06:52 PM #3273
Ok, I started getting these back from powder coat and I'll assemble them as I get some free time. I'm going to work my way down the list in the order they were requested, so no one panic if they haven't gottent a PM/email yet, it's going to take me a few days to get them all ready. I'm not skipping anyone. Still have all the uhmw to do on most of them
▪█──█▪ Equipment Crew #61 ▪█──█▪
-
01-23-2019, 04:09 PM #3274
-
01-23-2019, 05:22 PM #3275
-
01-23-2019, 05:36 PM #3276
-
-
01-24-2019, 05:44 AM #3277
[QUOTE=Mech6;1571869401]Ok, I started getting these back from powder coat and I'll assemble them as I get some free time. I'm going to work my way down the list in the order they were requested, so no one panic if they haven't gottent a PM/email yet, it's going to take me a few days to get them all ready. I'm not skipping anyone. Still have all the uhmw to do on most of them
I'm not the most keen when it comes to identifying equipment so can you tell me what these are or will be used for? Thanks in advance!
-
01-24-2019, 08:22 AM #3278
Safety strap brackets for racks with 5/8” holes. If getting these brackets from Mech, you’d just need to buy the straps separately.
See below link (which is for 1” hole racks):
https://www.sorinex.com/product/safety-strap-system/||---|| Rogue Barbell Club #36 ||---||
[M]===[6] Mech6 Crew #36 [M]===[6]
──<//>─<\\>── BWTG Cluster #36 ──<//>─<\\>──
-
01-24-2019, 08:53 AM #3279
-
01-24-2019, 11:10 AM #3280
Hey Mech. With the FT pulldown addition, couldn’t you widen the pulldown portion a bit and run the cables - swing arm > stack pulley > pulldown, rather than - swing arm > stack pulley > mount?
Ratio would stay the same, and there would be no need to clip an extra cable or have a cable lying around when not in use.
That thing could be the most complete all in one upper body piece ever. Awesome man!EQUIPMENT CREW VATO #72
PUB BURGERS / IMMERSIVE HORROR / OLD SCHOOL THRASH
-
-
01-24-2019, 11:28 AM #3281
Here is a reverse hyper attachment that I built. Easy(ish) design, stands on its own when not in use, and sets up very quickly. I have no plans to build any more, but design is yours if you want it.
https://www.instagram.com/p/BhNIWJvFIhB/EQUIPMENT CREW VATO #72
PUB BURGERS / IMMERSIVE HORROR / OLD SCHOOL THRASH
-
01-24-2019, 12:00 PM #3282
-
01-24-2019, 12:37 PM #3283
-
01-24-2019, 12:40 PM #3284
That is nice. Makes more sense than the rogue version that takes up half your rack permanently.
There's a very old one I made somewhere on this forum which was very simlar to yours except it was attached to rack and could be lifted and stored vertically at back when not in use.▪█──█▪ Equipment Crew #61 ▪█──█▪
-
-
01-24-2019, 01:04 PM #3285
-
01-24-2019, 03:28 PM #3286
That looks like it’s off their low bridge setup. It was on an Instagram post back in November too:
https://www.instagram.com/p/Bpskg-wjUss/||---|| Rogue Barbell Club #36 ||---||
[M]===[6] Mech6 Crew #36 [M]===[6]
──<//>─<\\>── BWTG Cluster #36 ──<//>─<\\>──
-
01-24-2019, 03:45 PM #3287
-
01-25-2019, 07:42 AM #3288
-
-
01-25-2019, 07:58 AM #3289
-
01-25-2019, 12:41 PM #3290
-
01-25-2019, 04:59 PM #3291
-
01-26-2019, 01:01 PM #3292
-
-
01-26-2019, 04:00 PM #3293
-
01-30-2019, 02:28 PM #3294
-
01-30-2019, 03:42 PM #3295
-
01-30-2019, 04:20 PM #3296
-
-
01-30-2019, 04:32 PM #3297
-
01-30-2019, 06:39 PM #3298
-
01-31-2019, 01:26 PM #3299
- Join Date: Aug 2013
- Location: Plano, Texas, United States
- Age: 49
- Posts: 204
- Rep Power: 774
Sorinex says on their website they are 32".
https://www.sorinex.com/product/dark...-strap-system/
-
01-31-2019, 03:11 PM #3300
Similar Threads
-
KimPossible Builds Her Competition Body
By KimPossible98 in forum JournalingReplies: 3609Last Post: 04-02-2012, 02:38 PM -
My Recent Deal Thread
By Keetman in forum Workout EquipmentReplies: 92Last Post: 02-11-2011, 06:57 AM
Bookmarks